Corsair Vengeance CMK16GX5M2B5200Z40 (16GB 2x8GB Kit/DDR5 5200MHz/CL40 40-40-40-77/1.25V/No RGB Anodized Aluminium Grey/Intel XMP 3.0 + AMD EXPO)
Consumercarts is reader-supported. When you buy through links on our site, we may earn a commission. As an Amazon Associate, we earn from qualifying purchases.
- Model:
- Corsair Vengeance|CMK16GX5M2B5200Z40|B Revision
- Capacity:
- 16GB|2x8GB Kit|8GB per Module
- Memory Type:
- DDR5|288-Pin DIMM|Non-ECC|Unbuffered
- Speed:
- 5200MHz|PC5-41600
- Timings:
- CL40|40-40-40-77
- Voltage:
- 1.25V
- Overclocking:
- Intel XMP 3.0|AMD EXPO
- Heat Spreader:
- Anodized Aluminum, No RGB|Compact Low-Profile Design
- Color Options:
- Grey
- Form Factor:
- Desktop DIMM
- Compatibility:
- Intel and AMD DDR5 Platforms|XMP 3.0 and EXPO Support
- Warranty:
- Limited Lifetime
Disclaimer: The price and specification of the given product may differ from the actual product. Please confirm on the retailer's website before buying.
Manufacturer: Corsair Last updated: September 7, 2026
The Corsair Vengeance CMK16GX5M2B5200Z40 is the non-RGB version of the 16GB (2x8GB) DDR5-5200 CL40 kit covered elsewhere on this site: same 40-40-40-77 secondary timings and 1.25V voltage, no lighting hardware, lower price. This is the entry point of Corsair's entire DDR5 range on this site, both in frequency and in price.
Performance and Timings
CL40 at 5200MHz gives roughly 15.4ns true latency, matching the RGB version of this kit exactly since lighting hardware has no bearing on timings. This is the loosest, lowest-frequency configuration in this product family, appropriate for budget builds or systems where memory speed isn't the limiting factor.
Compatibility
DDR5 only. Enable XMP 3.0 on Intel or EXPO on AMD to reach 5200MHz. As a lower, more universally supported frequency, this is among the least demanding DDR5 kits to get running on any board without QVL concerns.
Module Count and Rank
Two 8GB modules. Buy the capacity needed in one matched kit rather than combining separate kits later.
Design and Build
Plain anodized aluminium heat spreader, no lighting, grey finish, the shortest and least expensive configuration in this entire product family as a direct result of both the lower frequency tier and the absence of RGB.
Overclocking and BIOS Setup
Boots at JEDEC baseline until XMP or EXPO is enabled. Select the correct profile, choose 5200MHz CL40, save, reboot, verify in CPU-Z. This is the most straightforward kit in the family to get running cleanly on first boot given the lower target frequency.
Comparison to Sibling Products
Directly comparable to the RGB version of this exact kit, minus lighting and its cost. Against every 6000MHz-and-above kit covered elsewhere on this site, this trades meaningful performance for the lowest price point in the range; buyers who can stretch their budget to a 6000MHz kit will see a real, noticeable difference in gaming and general responsiveness.
Who This Kit Is Actually For
The most budget-constrained DDR5 buyers. The lowest price and frequency in this entire product family. Office and general-use systems. 5200MHz is more than adequate outside gaming and content creation workloads. Not for gaming builds, especially on AM5. 6000MHz is the frequency AMD recommends for the best fabric ratio; this sits well below that, and the gap is genuinely audible in frame-time consistency, not just synthetic benchmarks.
Expert Review
Rated by the Consumercarts editorial team, not by users
Best for
- The most budget-constrained DDR5 buyers
- Office and general-use systems
Not for
- gaming builds, especially on AM5